{"id":3552,"date":"2014-04-04T01:06:52","date_gmt":"2014-04-04T01:06:52","guid":{"rendered":"http:\/\/www.sabo-esp.com\/?page_id=3552"},"modified":"2014-11-13T20:09:14","modified_gmt":"2014-11-13T20:09:14","slug":"faqs-deposito-espumogeno-atmosfericos","status":"publish","type":"page","link":"https:\/\/www.sabo-esp.com\/en\/faqs\/faqs-deposito-espumogeno-atmosfericos\/","title":{"rendered":"FAQs – Foam Concentrate Tank"},"content":{"rendered":"

FAQs, Foam Concentrate Tank<\/p>\n

\n
The tube, which are connected the suction elements why not get to the bottom of the tank?<\/div>\n
\n

The suction tube is just biased and not in contact with the bottom, but reaches about 50 mm from it, this is to prevent suction positos, gels, etc. oxide plates, which eventually are deposited in the tank bottom.
\nThe ability of the same, when constructed, is already taken into account this “loss” of volume.<\/p>\n<\/div>\n<\/div>\n

\n
Why is there a diver for the tank filler tube?<\/div>\n
\n

To prevent foam formation when filling , since otherwise , if the foam is poured freely by dropping a single orifice from a height a large amount of foam which would prevent filling in a single operation would occur on deposit . With the dip tube is achieved by filling the foam from the bottom , so that this problem does not occur.<\/p>\n<\/div>\n<\/div>\n

\n
Do these proportioning may work in a different position to the horizontal?<\/div>\n
\n

The proportioning venturim\u00e9tricos have to work horizontally, which is its normal position, not vertical or inclined.
\nIn the case of the proportioning mod. SE-Z-ES and SE, the suction will be at the top while in the case where the mod. SE-PRO, the vacuum remains at the bottom.<\/p>\n<\/div>\n<\/div>\n

<\/p>\n

Foam Concentrate Tank<\/h3>\n

FAQs, Foam Concentrate Tank<\/p>\n

\n
The tube, which are connected the suction elements why not get to the bottom of the tank?<\/div>\n
\n

The suction tube is just biased and not in contact with the bottom, but reaches about 50 mm from it, this is to prevent suction positos, gels, etc. oxide plates, which eventually are deposited in the tank bottom.
\nThe ability of the same, when constructed, is already taken into account this “loss” of volume.<\/p>\n<\/div>\n<\/div>\n

\n
Why is there a diver for the tank filler tube?<\/div>\n
\n

To prevent foam formation when filling , since otherwise , if the foam is poured freely by dropping a single orifice from a height a large amount of foam which would prevent filling in a single operation would occur on deposit . With the dip tube is achieved by filling the foam from the bottom , so that this problem does not occur.<\/p>\n<\/div>\n<\/div>\n

\n
Do these proportioning may work in a different position to the horizontal?<\/div>\n
\n

The proportioning venturim\u00e9tricos have to work horizontally, which is its normal position, not vertical or inclined.
\nIn the case of the proportioning mod. SE-Z-ES and SE, the suction will be at the top while in the case where the mod. SE-PRO, the vacuum remains at the bottom.<\/p>\n<\/div>\n<\/div>\n

FAQs, Foam Concentrate Tank<\/p>\n

\n
The tube, which are connected the suction elements why not get to the bottom of the tank?<\/div>\n
\n

The suction tube is just biased and not in contact with the bottom, but reaches about 50 mm from it, this is to prevent suction positos, gels, etc. oxide plates, which eventually are deposited in the tank bottom.
\nThe ability of the same, when constructed, is already taken into account this “loss” of volume.<\/p>\n<\/div>\n<\/div>\n

\n
Why is there a diver for the tank filler tube?<\/div>\n
\n

To prevent foam formation when filling , since otherwise , if the foam is poured freely by dropping a single orifice from a height a large amount of foam which would prevent filling in a single operation would occur on deposit . With the dip tube is achieved by filling the foam from the bottom , so that this problem does not occur.<\/p>\n<\/div>\n<\/div>\n

\n
Do these proportioning may work in a different position to the horizontal?<\/div>\n
\n

The proportioning venturim\u00e9tricos have to work horizontally, which is its normal position, not vertical or inclined.
\nIn the case of the proportioning mod. SE-Z-ES and SE, the suction will be at the top while in the case where the mod. SE-PRO, the vacuum remains at the bottom.<\/p>\n<\/div>\n<\/div>\n

<\/p>","protected":false},"excerpt":{"rendered":"

The proportioning venturim\u00e9tricos have to work horizontally, which is its normal position, not vertical or inclined. In the case of the proportioning mod. SE-Z-ES and SE, the suction will be at the top while in the case where the mod. SE-PRO, the vacuum remains at the bottom.<\/p>\n","protected":false},"author":1,"featured_media":0,"parent":1542,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"template-sidebar-right.php","meta":[],"_links":{"self":[{"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/pages\/3552"}],"collection":[{"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/pages"}],"about":[{"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/types\/page"}],"author":[{"embeddable":true,"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/comments?post=3552"}],"version-history":[{"count":4,"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/pages\/3552\/revisions"}],"predecessor-version":[{"id":3790,"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/pages\/3552\/revisions\/3790"}],"up":[{"embeddable":true,"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/pages\/1542"}],"wp:attachment":[{"href":"https:\/\/www.sabo-esp.com\/en\/wp-json\/wp\/v2\/media?parent=3552"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}